Go to the first, previous, next, last section, table of contents.


You can use the updating commands to:

You can also use the commands to update all the nodes and menus in a region or in a whole Texinfo file.

The updating commands work only with conventional Texinfo files, which are structured hierarchically like books. In such files, a structuring command line must follow closely after each @node line, except for the `Top' @node line. (A structuring command line is a line beginning with @chapter, @section, or other similar command.)

You can write the structuring command line on the line that follows immediately after an @node line or else on the line that follows after a single @comment line or a single @ifinfo line. You cannot interpose more than one line between the @node line and the structuring command line; and you may interpose only an @comment line or an @ifinfo line.

Commands which work on a whole buffer require that the `Top' node be followed by a node with an @chapter or equivalent-level command. The menu updating commands will not create a main or master menu for a Texinfo file that has only @chapter-level nodes! The menu updating commands only create menus within nodes for lower level nodes. To create a menu of chapters, you must provide a `Top' node.

The menu updating commands remove menu entries that refer to other Info files since they do not refer to nodes within the current buffer. This is a deficiency. Rather than use menu entries, you can use cross references to refer to other Info files. None of the updating commands affect cross references.

Texinfo mode has five updating commands that are used most often: two are for updating the node pointers or menu of a single node (or a region); two are for updating every node pointer and menu in a file; and one, the texinfo-master-menu command, is for creating a master menu for a complete file, and optionally, for updating every node and menu in the whole Texinfo file.

The texinfo-master-menu command is the primary command:

C-c C-u m
M-x texinfo-master-menu
Create or update a master menu that includes all the other menus (incorporating the descriptions from pre-existing menus, if any). With an argument (prefix argument, C-u, if interactive), first create or update all the nodes and all the regular menus in the buffer before constructing the master menu. (See section The `Top' Node and Master Menu, for more about a master menu.) For texinfo-master-menu to work, the Texinfo file must have a `Top' node and at least one subsequent node. After extensively editing a Texinfo file, you can type the following:
C-u M-x texinfo-master-menu
or
C-u C-c C-u m
This updates all the nodes and menus completely and all at once.

The other major updating commands do smaller jobs and are designed for the person who updates nodes and menus as he or she writes a Texinfo file.

The commands are:

C-c C-u C-n
M-x texinfo-update-node
Insert the `Next', `Previous', and `Up' pointers for the node that point is within (i.e., for the @node line preceding point). If the @node line has pre-existing `Next', `Previous', or `Up' pointers in it, the old pointers are removed and new ones inserted. With an argument (prefix argument, C-u, if interactive), this command updates all @node lines in the region (which is the text between point and mark).
C-c C-u C-m
M-x texinfo-make-menu
Create or update the menu in the node that point is within. With an argument (C-u as prefix argument, if interactive), the command makes or updates menus for the nodes which are either within or a part of the region. Whenever texinfo-make-menu updates an existing menu, the descriptions from that menu are incorporated into the new menu. This is done by copying descriptions from the existing menu to the entries in the new menu that have the same node names. If the node names are different, the descriptions are not copied to the new menu.
C-c C-u C-e
M-x texinfo-every-node-update
Insert or update the `Next', `Previous', and `Up' pointers for every node in the buffer.
C-c C-u C-a
M-x texinfo-all-menus-update
Create or update all the menus in the buffer. With an argument (C-u as prefix argument, if interactive), first insert or update all the node pointers before working on the menus. If a master menu exists, the texinfo-all-menus-update command updates it; but the command does not create a new master menu if none already exists. (Use the texinfo-master-menu command for that.) When working on a document that does not merit a master menu, you can type the following:
C-u C-c C-u C-a
or
C-u M-x texinfo-all-menus-update
This updates all the nodes and menus.

The texinfo-column-for-description variable specifies the column to which menu descriptions are indented. By default, the value is 32 although it is often useful to reduce it to as low as 24. You can set the variable with the M-x edit-options command (see section `Editing Variable Values' in The GNU Emacs Manual) or with the M-x set-variable command (see section `Examining and Setting Variables' in The GNU Emacs Manual).

Also, the texinfo-indent-menu-description command may be used to indent existing menu descriptions to a specified column. Finally, if you wish, you can use the texinfo-insert-node-lines command to insert missing @node lines into a file. (See section Other Updating Commands, for more information.)


Go to the first, previous, next, last section, table of contents.