Go to the first, previous, next, last section, table of contents.


Setting breakpoints

Breakpoints are set with the break command (abbreviated b). The debugger convenience variable `$bpnum' records the number of the breakpoint you've set most recently; see section Convenience variables, for a discussion of what you can do with convenience variables.

You have several ways to say where the breakpoint should go.

break function
Set a breakpoint at entry to function function. When using source languages that permit overloading of symbols, such as C++, function may refer to more than one possible place to break. See section Breakpoint menus, for a discussion of that situation.
break +offset
break -offset
Set a breakpoint some number of lines forward or back from the position at which execution stopped in the currently selected stack frame. (See section Stack frames, for a description of stack frames.)
break linenum
Set a breakpoint at line linenum in the current source file. The current source file is the last file whose source text was printed. The breakpoint will stop your program just before it executes any of the code on that line.
break filename:linenum
Set a breakpoint at line linenum in source file filename.
break filename:function
Set a breakpoint at entry to function function found in file filename. Specifying a file name as well as a function name is superfluous except when multiple files contain similarly named functions.
break *address
Set a breakpoint at address address. You can use this to set breakpoints in parts of your program which do not have debugging information or source files.
break
When called without any arguments, break sets a breakpoint at the next instruction to be executed in the selected stack frame (see section Examining the Stack). In any selected frame but the innermost, this makes your program stop as soon as control returns to that frame. This is similar to the effect of a finish command in the frame inside the selected frame--except that finish does not leave an active breakpoint. If you use break without an argument in the innermost frame, stops the next time it reaches the current location; this may be useful inside loops. normally ignores breakpoints when it resumes execution, until at least one instruction has been executed. If it did not do this, you would be unable to proceed past a breakpoint without first disabling the breakpoint. This rule applies whether or not the breakpoint already existed when your program stopped.
break ... if cond
Set a breakpoint with condition cond; evaluate the expression cond each time the breakpoint is reached, and stop only if the value is nonzero--that is, if cond evaluates as true. `...' stands for one of the possible arguments described above (or no argument) specifying where to break. See section Break conditions, for more information on breakpoint conditions.
tbreak args
Set a breakpoint enabled only for one stop. args are the same as for the break command, and the breakpoint is set in the same way, but the breakpoint is automatically deleted after the first time your program stops there. See section Disabling breakpoints.
hbreak args
Set a hardware-assisted breakpoint. args are the same as for the break command and the breakpoint is set in the same way, but the breakpoint requires hardware support and some target hardware may not have this support. The main purpose of this is EPROM/ROM code debugging, so you can set a breakpoint at an instruction without changing the instruction. This can be used with the new trap-generation provided by SPARClite DSU and some x86-based targets. These targets will generate traps when a program accesses some data or instruction address that is assigned to the debug registers. However the hardware breakpoint registers can take a limited number of breakpoints. For example, on the DSU, only two data breakpoints can be set at a time, and will reject this command if more than two are used. Delete or disable unused hardware breakpoints before setting new ones (see section Disabling breakpoints). See section Break conditions.
thbreak args
Set a hardware-assisted breakpoint enabled only for one stop. args are the same as for the hbreak command and the breakpoint is set in the same way. However, like the tbreak command, the breakpoint is automatically deleted after the first time your program stops there. Also, like the hbreak command, the breakpoint requires hardware support and some target hardware may not have this support. See section Disabling breakpoints. See also section Break conditions.
rbreak regex
Set breakpoints on all functions matching the regular expression regex. This command sets an unconditional breakpoint on all matches, printing a list of all breakpoints it set. Once these breakpoints are set, they are treated just like the breakpoints set with the break command. You can delete them, disable them, or make them conditional the same way as any other breakpoint. The syntax of the regular expression is the standard one used with tools like `grep'. Note that this is different from the syntax used by shells, so for instance foo* matches all functions that include an fo followed by zero or more os. There is an implicit .* leading and trailing the regular expression you supply, so to match only functions that begin with foo, use ^foo. When debugging C++ programs, rbreak is useful for setting breakpoints on overloaded functions that are not members of any special classes.
info breakpoints [n]
info break [n]
info watchpoints [n]
Print a table of all breakpoints, watchpoints, and catchpoints set and not deleted, with the following columns for each breakpoint:
Breakpoint Numbers
Type
Breakpoint, watchpoint, or catchpoint.
Disposition
Whether the breakpoint is marked to be disabled or deleted when hit.
Enabled or Disabled
Enabled breakpoints are marked with `y'. `n' marks breakpoints that are not enabled.
Address
Where the breakpoint is in your program, as a memory address.
What
Where the breakpoint is in the source for your program, as a file and line number.
If a breakpoint is conditional, info break shows the condition on the line following the affected breakpoint; breakpoint commands, if any, are listed after that. info break with a breakpoint number n as argument lists only that breakpoint. The convenience variable $_ and the default examining-address for the x command are set to the address of the last breakpoint listed (see section Examining memory). info break displays a count of the number of times the breakpoint has been hit. This is especially useful in conjunction with the ignore command. You can ignore a large number of breakpoint hits, look at the breakpoint info to see how many times the breakpoint was hit, and then run again, ignoring one less than that number. This will get you quickly to the last hit of that breakpoint.

allows you to set any number of breakpoints at the same place in your program. There is nothing silly or meaningless about this. When the breakpoints are conditional, this is even useful (see section Break conditions).

itself sometimes sets breakpoints in your program for special purposes, such as proper handling of longjmp (in C programs). These internal breakpoints are assigned negative numbers, starting with -1; `info breakpoints' does not display them.

You can see these breakpoints with the maintenance command `maint info breakpoints'.

maint info breakpoints
Using the same format as `info breakpoints', display both the breakpoints you've set explicitly, and those is using for internal purposes. Internal breakpoints are shown with negative breakpoint numbers. The type column identifies what kind of breakpoint is shown:
breakpoint
Normal, explicitly set breakpoint.
watchpoint
Normal, explicitly set watchpoint.
longjmp
Internal breakpoint, used to handle correctly stepping through longjmp calls.
longjmp resume
Internal breakpoint at the target of a longjmp.
until
Temporary internal breakpoint used by the until command.
finish
Temporary internal breakpoint used by the finish command.
shlib events
Shared library events.


Go to the first, previous, next, last section, table of contents.